Introduction

This document explains how to install the charging base for the PAX A920 or A920 Pro terminal and included silicone sleeve. The charging base makes it easy to recharge the terminal without having to remove the silicone sleeve to ensure that the USB power connector is properly seated in the terminal’s charging port.

Installing the Terminal Charging Base

Before you install and connect the charging base, make sure that the desired location is within reach of an AC outlet and that there is enough space to for the charging base and the terminal when connected.

To install the charging base:

1. Turn the charging base over and locate the USB connection port.

   A920

A920 Pro

1. Insert the cable’s micro-USB (A920) or USB Type-C (A920 Pro) plug into the base’s connection port.

A920

A920 Pro

1. Secure the cable in the guide at the top of the charging base and turn the charging base over.

A920

A920 Pro

1. Connect the cable’s USB plug into the AC adapter’s USB port.

A920

A920 Pro

1. Plug the adapter into an AC outlet. The LED at the bottom edge of the base lights up.

Installing the Terminal Silicone Sleeve

To protect your PAX A920 or A920 Pro terminal from minor impact damage, you should install the silicone sleeve provided with the terminal charging base as the charging base is designed specifically for terminals with the sleeve.

To install the silicone sleeve:

1. Insert the top of the terminal into the sleeve's printer protection until the sleeve fits snugly onto the terminal’s top.

2. Pull the bottom of the sleeve over the bottom edge of the terminal.

3. Repeat for any additional terminals you intend to place on the charging base.

Requirement

To ensure the best charging results, you must use the original AC power adapter that came with your PAX A920 or A920 Pro terminals. The AC power adapter should have the PAX logo printed on one side as shown below:

Overview

Your multi-terminal charging base comes with the following:

Base Components

The following images show the location of the main charging base components:

1. AC power cord

2. Multi-terminal charging bases (x5)

3. USB charging cables (x5)

4. Six (6) outlet power bar

To use the charging base, you need only place the terminal(s) vertically on the base so the printer rests in the cradle at the top of the charging base.

A920

Charging Base

Requirement

To ensure the best charging results, you must use the original AC power adapter that came with your PAX A920 or A920 Pro terminal. The AC power adapter should have the PAX logo printed on one side as shown below:

Powering the Charging Base On or Off

The multi-terminal charging base has a power switch on the attached power bar, shown below:

• To power on the terminal charging base, make sure the power cord is plugged into a grounded AC outlet and that the power switch is in the On/RESETposition; the switch lights up with a red indicator, as shown below:

• To power off the terminal charging base, you can either push the power switch to the OFF position or unplug the power cord from the grounded AC outlet.

Charging Terminals

To use the charging base, you need only place the terminal(s) vertically on the base so the printer rests in the cradle at the top of the charging base.

If the status light remains blue after you place the terminal on the base, the terminal is not seated correctly, and not connecting to the base’s gold charging contacts.

LED Status Light

The LED at the bottom edge of the charging base indicates the terminal’s charging status:

Installing the Multi-Terminal Charging Base

Before you install and connect the multi-terminal charging base, make sure that the desired location is within reach of an AC outlet and that there is enough space to for the charging base and the terminals when connected.

To install the multi-terminal charging base:

1. Collect the original AC power adapters that were shipped with your PAX A920 or A920 Pro terminals (maximum of 5 per multi-terminal charging base).

1. Turn the multi-terminal charging base over to access the opening on the bottom.

2. Remove any twist ties that secure the charging cables together. Do not remove any of the nylon zip ties as each cable should be long enough to reach an outlet on the power bar.

1. Working one cable at a time, connect the cable’s USB plug into the AC adapter’s USB port.

1. Plug the adapter into an outlet on the power bar.

1. Repeat steps 4 and 5 for each additional charging cable.

2. After you connect all 5 cables to the power bar, plug in the power bar's cable to an available AC outlet.

3. If it is not already, switch the power bar's power button to the On/RESETposition; the switch lights up with a red indicator and the LEDs at the bottom edge of the charging bases light up.

1. Turn the multi-terminal charging base over to place it securely in its desired location. The base is ready to begin charging your terminals.

Installing Terminal Silicone Sleeves

To protect your PAX A920 or A920 Pro terminals from minor impact damage, you should install the silicone sleeves provided with the multi-terminal charging base as the charging bases are designed specifically for terminals with the sleeve.

To install the silicone sleeve:

1. Insert the top of the terminal into the sleeve's printer protection until the sleeve fits snugly onto the terminal’s top.

2. Pull the bottom of the sleeve over the bottom edge of the terminal.

3. Repeat for every terminal you intend to place on the charging bases.